@BZ_Shop Official: Instagram | Linktree

BZ Shop Etsy Page

Please find the product below or select your product on Etsy and view the “Item details”; instructions will be towards the bottom. 

Looking for Install Instructions?

1. Open desired panel and remove the latch mounting screw and mounting bracket with appropriate screwdriver or socket. Set both aside for reinstallation. 

2. Push lock from inside of the panel towards the exterior.

3. Remove original thin rubber gasket. The rubber gasket will not be used so can be stored or thrown away.  

4. Orient the latch cover as desired and drop latch into the latch cover recess.

5. Properly orientate latch & latch cover and install back into panel.

6. Reattach mounting bracket and screw to the backside of the latch. 

7. Enjoy!

Latch Cover Install

1. With everything disassembled, place the back plate into the door ribs so that the textured side faces towards the outer door edges. (The plate should be flush in-between the door ribs)

2. Take the bolts and thread them through the plate into one of the arms being careful not to cross thread or overtighten. Tighten the bolts down until snug using a 4mm hex key making sure the arm is flat against the rib and not hung up on the door latch cable.

3. Repeat step (2) for other side.

4. Hold a paper towel between the arms and thread the large "bolts" through the arm into the paper towel.

5. Tighten the large "bolts" until flush and snug with the arm.

6. To remove the paper towel, just unscrew both "bolts" and follow steps (4-5) to reinstall.

Paper Towel Holder Install

1. Insert the Baja Design Rock lights & CAREFULLY screw down the light by hand until it is snuggly in place (Do NOT rush this process or you will run the risk of breaking the part).
2. Feed wires from rock lights through the channel on the housing. The two inner most light wires will be routed on top of the outer most. *Silicone can be center hole to keep everything in place*
3. Remove old brake light and applicable wiring from camper. 
4. Install Brake Light Housing with bolts/washers included with BD rock lights.
5. Feed rock light wires through existing hole in campers panel making sure wires stay in the housing channels. 
5a. optional but recommended: Use silicone to seal the panel hole where the wires enter. This will prevent water/dust ingress and can also help keep the housing firmly pressed against the panel. 
6. Wire up lights. **Refer to BD suggested wiring or seek a pro

Baja Designs Brake Light Install

1. Take the Dometic puck base and line the small drainage hole with the one on the purchased mount.

2. Once the holes are lined up, firmly press the puck into the mount.

3. Depending on your mount, either bolt it to the desired surface or hook the mount into the molle

Dometic Faucet Mount Install

"L": Large covers
"S": Standard covers

1. Line up one side of the cover and firmly press into place. It can be easier to press the cover in at the middle of the slot and then slid into the corner. 

2. Once the side is pressed into place, work your way across the cover. The covers will take some force but make sure they are flush around all edges.

3. Now you are all set! Repeat the process as many times as needed until all covers are set into desired location. 


*Note: Covers will need to be cut around your specific camper mounts.

SP Wire Channel Covers Install

**Please note there is a small dot on the back of some plugs. This will help properly differentiate/orientate them for install.**

One Dot: Square Plug, Point dot towards exterior of the camper

Two Dots: Rectangular Plug, Point dots towards truck cab

No Dots: Plug can be easily orientated in any direction

SP Wire Channel Plugs Install

GFC:
The mount will be affixed using (4) 10-32nd bolts and accompanying Tnuts [not included].
1. Once the mount & Tnuts are loosely attached to the T-track, slide the mount all the way against the billet latches at the rear of the tent.

2. Snug the bolts down once the mount is in place. Do not over-tighten! 

3. Now you are all set to slide the starlink into the mount.

Super Pacific:
The mount will be affixed using (2) M6 bolts, flat washer and Tnuts [hardware not included].

1. Once the mount & Tnuts are loosely attached to the T-track, slide the mount all the way to the rear of the T-track while making sure the Tnuts are in the track.

2. Snug the bolts down once the mount is in place. Do not over-tighten! 

3. Now you are all set to slide the starlink into the mount.

**DO NOT DRIVE WITH DISH INSTALLED ON THE MOUNT**

Starlink Mount Install 

Questions or Requests?

@BZ_Shop

Joy and Vigilance: A Pride Reflection

Not All Clicks Are Equal: A Year of Linktree Traffic, by Source

Your bio link is the internet's busiest intersection

What happens after the listen: Linktree’s trending Podcast(er)s Pulse, April 2026

How many followers do you need to make money on Instagram in 2026?

Linktree Enhances Insights Chat With Personalized, Data-Driven Recommendations

How to Generate Passive Income by Selling Digital Products and Growing Your Online Audience

Enjoy 30 days of Hulu for FREE

Claim 10 free meals* from HelloFresh

Get 60% off Sitewide

Sip your way to stronger health with 30% off at ARMRA

Save 10% at Omnilux LED

Save 10% on Ritual Multivitamins Subscriptions

You've scored 50% OFF Factor 🤤

Join now and get 50% off a Club membership

Get your first box FREE with Curology!

Claim your $20 bonus with Acorns

Sign up for Headspace Today and get a 14 day free trial!

Get AAA membership for half the price!

Get 30¢/gal cash back on gas at major stations

Get 15% off at Equip Foods

20% Off the at FabFitFun with code INSIDER20

Get 80% off your first order when signing up to be a VIP!

Get 15% off for cleaner skin at CLEARSTEM

Get your first box FREE with Agency!

50% off + Free Shipping at Purple Carrot!

Power Up with Daily Harvest's High-Protein Smoothies

Save $100 with Gobble

Save 10% on your First Maev Order!

15% off your favorite non-alcoholic spirits at The Zero Proof

10% off JLab’s award‑winning audio gear

Get help with or without insurance. Use code SPACE80 for $80 off.

Start speaking a new language in just 3 weeks

@BZ_Shop

Welcome to BZ Shop!

About this account

More from Linktree